聯系我們
新河縣鼎弘重工機械有限公司
手機:18032964888
電話:0319-4888-880
聯系人:趙經理
網址:www.machine-com.com
地址:河北省邢台市新河縣城西工業區
當前位置首頁 >> 鑄鐵閘門的門槽與板面爲整體安裝
鑄鐵閘門的門槽與板面爲整體安裝
[來源:來自網絡] [作者:aowl] [日期:22-05-18] [浏覽次數:]

鑄鐵閘門的門槽與板面爲整體安裝,二次浇注方式(亦可一次性整体安装浇注),浇注前以密封止水面及侧向导轨面为基准将闸框调正,固定,撑好背面防止变形,进行浇注砼浆一定要密封实以防渗漏。 Cast iron gate of gate slot and the plate for the whole installation, the second pouring way (can be one-time whole installation pouring), to seal check before pouring water and lateral guide surface as a benchmark to brake adjustment, fixed, maintain good prevent deformation, on the back of pouring concrete slurry must be sealed to prevent leakage.   铸铁闸门安装浇注砼前,调整闸门与闸框偏心与间隙,锁紧楔块装置.以达到良好的止水效果。铸铁闸门的板面与闸槽为偶合件配套,在搬运、仓储及安装时不得互换,以免影响止水效果。 Before the casting of cast-iron gate is installed, adjust the gate and the gate eccentric and clearance and lock the wedge device. To achieve a good water stop effect. The plate and sluice gate of the cast iron gate are the supporting parts of the coupling parts. They are not interchangeable in handling, storage and installation so as to avoid the effect of water stop.   闸门的迎水面一定要按设计要求安装否则因板面受力方向不对,引起板面断裂,遇反向受压时一定要在订货时说明,防止发生重大事故。在订货时要提供孔口尺寸,水头,提升高度和结构形式,闸板面一般为正向(迎水面)受压,如需反向受压,订货时需说明,止水一般是后止水(背水面),需前止水时,订货时应说明,使用时必须按操作规程操作。 The face of the gate must be installed according to the design requirement, because the force of the plate face is not right, cause the plate surface fracture, when the reverse compression must be specified in the order, prevent a major accident. In order to provide the orifice size, head, hoisting height and structural form, the disc surface is generally positive (meet) the water pressure, such as the need to reverse pressure, when placing order, indicate that water is generally after water stop (back) the water, need water, before when you order it should be, must be in accordance with the operating procedures.   经常检查闸门板与闸槽是否卡涩,及时将卡涩物清除,保证位置置中,使设备正常运行。本厂的铸铁闸是按照CJ/T3006—92供水排水铸铁闸门标准和DL/T5018—94规范设计制造。 Check whether the gate plate and the sluice gate are too dry, remove the carbule in time, ensure the position of the equipment, and make the equipment run normally. The casting iron gate of our factory is designed and manufactured according to the standard of CJ/t3006-92 water supply and drainage cast iron gate and DL/t5018-94.   使用与保养 Use and maintenance   1、使用手动啓閉機开启、关闭闸门时,用力应均匀,切勿用力过猛,以防损坏(伤)定位装置。 1. When opening and closing the gate with a manual hoist, force should be evenly applied and not too hard to prevent damage (injury) positioning device.   2、使用手电两用啓閉機启闭闸门时,应注意到: 2. When using a flashlight to open and close the gate, it should be noted that:   a、用电动启闭时,应检查手摇柄是否脱离转轴,以免在启动时碰伤人员。 A. When using electric opening and closing, check whether the handle of the hand is out of the shaft, so as not to injure personnel at startup.   b、用手动启闭时,应切断电源,将摇柄插入孔内摇动(或将电动装置上的电动标记切入到手动标志上去)。 B. When opening and closing manually, the power should be cut off, and the rocker shall be inserted into the hole to shake (or cut the electric mark on the electric device to the manual sign).   c、每2-3个月对啓閉機轴承,传动螺杆、螺母等加注1-2次润滑液,大保养时,应给轴承部分注满牛油。 C, each 2-3 months to open and close machine bearing, drive screw, nut and so on 1-2 lubrication fluid, big maintenance, should give the bearing part full of butter.   d、每年需对闸门作一次油漆、防腐处理。 D. each year, the gate should be painted and embalmed

返首頁:www.machine-com.com